![]() ![]() ![]() ![]() ![]()
![]() 420111, г. Казань, Телефоны:(843) 238-58-10E-mail:vestnik.kstu-kai@yandex.ru
|
АннотацииЭнергосиловые установкиМОДЕЛИ ФОРМЫ И РАЗМЕРОВ ПЛАМЕНИ НЕОДНОРОДНЫХ УГЛЕВОДОРОДО-ВОЗДУШНЫХ СМЕСЕЙ В.А. Щукин, канд. техн. наук, О.В. Дунай, канд. техн. наук Представлены модели формы пламени при различной степени неоднородности смеси на входе в камеру сгорания. Размеры факела пламени неоднородных смесей определялись на основе представлений классической теории горения о размерах простейших видов пламени, но с учетом явления флуктуационного реагирования при горении. Models for flame shape and dimensions of non-homogeneous air-hydrocarbon mixturesV.A. Shchukin and O.V. Dunai We present here some models for the flame form at different degrees of mixture inhomogeneity at combustion chamber inlet. The dimensions of the torch-like flame of non-homogeneous mixtures are determined here using as the base the knowledge of classical theory of flame combustion theory, but with proper account for fluctuation effect of combustion. УДК 620.9,621.577 АНАЛИЗ СХЕМНЫХ РЕШЕНИЙ РАЗЛИЧНЫХ ТЕПЛОНАСОСНЫХ УСТАНОВОКВ.М. Гуреев, канд. техн. наук, Ю.Ф. Гортышов, докт. техн. наук, Представлено схемное решение парокомпрессионной теплонасосной установки с газомоторным приводом и результаты технико-экономических расчетов ее характеристик. On the analysis of design decisions for different heat pump systemsV.M. Gureyev, Yu.F. Gortyshov, A.M. Yermakov, and M.V. Gureyev In this paper, we present an engineering decision for the vapor compression heat pump system equipped with the gas motor drive. Also presented are the data of technical and economical calculations of the system performance. Технология машиностроенияУДК 621.436-233.2.001.5 ОЦЕНКА КОМПЛЕКСА ПАРАМЕТРОВ ШАТУННОГО ПОДШИПНИКА МЕТОДОМ ИЗМЕРЕНИЯ ЭЛЕКТРОСОПРОТИВЛЕНИЯ КОНТАКТАВ.Н. Никишин, канд. техн. наук, С.В. Сибиряков, ст. преподаватель Представлены результаты экспериментальных исследований триботехнических характеристик шатунного подшипника в зависимости от комплекса параметров. Определены предельные допустимые нагрузки, зазоры и температуры подшипника по параметру обеспечения жидкостного трения. Integrated assessment of the crankshaft rod bearing quality with use of the method of contact resistance measurementV.N. Nikishin and S.V. Sibiryakov We present here some experimental data on tribotechnical characteristics of the crankshaft rod bearings and determine the ultimate permissible loads, rod bearing clearances, and temperatures by using as the base the fluid friction parameter. УДК 621.9.047 621.9.048 УПРАВЛЕНИЕ ПРОЦЕССОМ КОМБИНИРОВАННОЙ (ЭЛЕКТРОАЛМАЗНОЙ) ОБРАБОТКИ ВЫСОКОТВЕРДЫХ МАТЕРИАЛОВ И.И. Хафизов, ст. преподаватель, З.Б. Садыков, докт. техн. наук Рассмотрены электрофизические и электрохимические методы формообразования деталей и их комбинации; представлена история развития электрохимии в этой области. Изучены вопросы управления процессом комбинированной (электроалмазной) обработки высокотвердых материалов. Исследован электроалмазный способ обработки сплавов: особенности и основные факторы, влияющие на эффективность процесса обработки. On a control of processes at combined electric diamond machining of very hard materialsI.I. Khafizov and Z.B. Sadykov In this paper, we consider some electrophysical and electrochemical methods of parts shaping and their combinations and present the history of electrochemistry development in this field. We examined also some problems connected with the control of processes at combined electric diamond machining of very hard materials. Also investigated is the method of electric diamond machining of alloys as well as some basic peculiarities and factors influencing upon the machining efficiency. УДК 621.9.044.621.791 МОДЕЛИРОВАНИЕ ПРОЦЕССА ФОРМИРОВАНИЯ ШЕРОХОВАТОСТИ ОБРАБОТАННОЙ ПОВЕРХНОСТИ, ОБРАЗУЕМОЙ ЭЛЕКТРИЧЕСКОЙ ОБРАБОТКОЙ КОНТАКТНЫМ НЕПРЕРЫВНЫМ ОПЛАВЛЕНИЕМ Ф.А. Шамсутдинов, канд. техн. наук, Д.Г. Насыров, аспирант Установлен механизм формирования микрогеометрии обрабатываемой поверхности, образуемой электрической обработкой контактным непрерывным оплавлением. Получены и экспериментально подтверждены расчетные зависимости оценки качества поверхности на операциях разрезания. Впервые для моделирования процесса формирования обработанной поверхности применены методы гидродинамики и теории пограничного слоя. Simulation of processes at forming of roughneess on the neat surfaces during electrical machining by contact continuous fusionF.A. Shamsutdinov and D.G. Nasyrov We suggest here using a mechanism for forming of machined surface micro-geometry during the electrical Измерительные и управляющие системыУДК 681.78 МЕТОДИКА РАСЧЕТА ПАРАМЕТРОВ ОПТИЧЕСКОГО КАНАЛА С УЧЕТОМ ПАРАМЕТРОВ АТМОСФЕРЫ В.В. Рожин , канд. техн. наук, Т.Р. Габдрахманов, аспирант, Известное уравнение локации (источник излучения, оптический канал, фотоприемник) представляется аппаратной функцией и уравнением устройства с единичными параметрами. При этом учитывается время относительной неработоспособности устройства за год из-за плохих погодных условий на основе современных статистических данных. On a technique for calculating the optical channel parameters with account for atmospheric parametersV.V. Rozhin , T.R. Gabdrakhmanov, and A.V. Starostin The well-known equation of location (source of emission, optical channel, photodetector) is represented here in the form of the spread function and equation for the device with unit parameters. Based on the modern statistical data, we take account hereby of time periods of the device relative nonoperability due to unfavorable weather conditions. УДК 629.7.054.44:629.7.05.67 АЛГОРИТМИЧЕСКАЯ КОРРЕКЦИЯ ПОГРЕШНОСТЕЙ СИСТЕМЫ ИЗМЕРЕНИЯ МАЛЫХ ВОЗДУШНЫХ СКОРОСТЕЙ ВЕРТОЛЕТА В.В. Солдаткин, канд. техн. наук Рассматривается структурно-функциональная схема системы измерения малых воздушных скоростей вертолета (СИМВС-В) на основе неподвижного проточного многоканального аэрометрического приемника и струйно-конвективных (термоанемометрических) измерительных каналов. Приводится статическая характеристика термоанемометрических преобразователей и ее аппроксимация по экспериментальным данным. Раскрывается методика алгоритмической коррекции погрешностей СИМВС-В, связанных с неидентичностью характеристик термоанемометрических преобразователей. Приводится оценка остаточных погрешностей каналов СИМВС-В. Algorithmic correction of errors in the helicopter’s system of low airspeed measurementV.V. Soldatkin Based on the aerometric immovable multi-channel flow-passage receiver and the jet-convective channels, we consider here the structural functional scheme of the helicopter’s system of low airspeed measurement. Using the experimental data as the base, we present also the static characteristic of hot-wire transducers, its approximation as well as the technique for algorithmic correction of the helicopter’s system errors due to variations in the hot-wire transducer characteristics. Also given is the assessment of residual errors of the helicopter’s system channels. РадиоэлектроникаУДК 621.382.049.776 ПРИМЕНЕНИЕ ПЕРСОНАЛЬНОГО КОМПЬЮТЕРА ДЛЯ РАСЧЕТА ПРЕЦИЗИОННЫХ РЕЗИСТИВНЫХ ЭЛЕМЕНТОВ ИНТЕГРАЛЬНЫХ СХЕМ ПО МЕТОДИКЕ, УЧИТЫВАЮЩЕЙ КОНТАКТНЫЕ СОПРОТИВЛЕНИЯ В.И. Крючатов, канд. техн. наук Предложена новая методика автоматизированного расчета прецизионных резистивных элементов интегральных схем с учетом контактных сопротивлений. Разработан алгоритм и программные модули расчета резисторов для персонального компьютера. Программа написана на языке DALPHI-5 и работает в операционной среде Windows. PC application in calculations of precise resistive IC elements with use of contact resistance techniqueV.I. Kryuchatov We present here the new technique for conducting the computer-assisted calculations of precise resistive IC elements with account for contact resistances. Also presented the algorithm and a number of programming modules for calculating the nominal values of resistors used in PCs. The program is written in DALPHI-5 and uses the Windows operating environment. УДК 519.6+621.373 ВЛИЯНИЕ КВАЗИРЕЗОНАНСНЫХ УПРАВЛЯЮЩИХ ВОЗДЕЙСТВИЙ НА КОРРЕЛЯЦИОННЫЕ ХАРАКТЕРИСТИКИ СИГНАЛОВ, ФОРМИРУЕМЫХ НА ОСНОВЕ СИСТЕМЫ ЛОРЕНЦА В.В. Афанасьев, докт. техн. наук, С.С. Логинов, аспирант, Рассмотрено влияние квазирезонансных управляющих воздействий на корреляционные характеристики сигналов, формируемых на основе нелинейной системы Лоренца с динамическим хаосом математическим моделированием и проведено сопоставление различных видов воздействий на параметры системы Лоренца. Даны рекомендации по выбору типа воздействия с точки зрения их энергетической эффективности и наибольшего сокращения интервалов корреляции формируемых сигналов. Influence of quasi-resonance control actions on the correlation characteristics of signals formed with use of the Lorentz’s systemV.V. Afanas’yev, S.S. Loginov, and Yu.E. Pol’skii We consider here influence exerted by the quasi-resonance control actions upon the correlation characteristics of signals formed with use of the nonlinear dynamically chaotic Lorentz’s system. We compared a number of different kinds of actions on the Lorentz’s system parameters and worked out the recommendations on the selection of action kind by proceeding from their energetic efficiency and the largest reduction of intervals of signals correlation. Математика и механикаУДК 535.41:534.1 ИССЛЕДОВАНИЕ РЕЗОНАНСНЫХ ЧАСТОТ И ФОРМ КОЛЕБАНИЙ ДИСКА ПОСТОЯННОЙ ТОЛЩИНЫ С ПРИМЕНЕНИЕМ ГОЛОГРАФИЧЕСКОЙ ИНТЕРФЕРОМЕТРИИ Р.Х. Макаева, канд. техн. наук, А.М. Царева, ассистент, Приводятся результаты исследований резонансных частот и форм колебаний диска постоянной толщины, закрепленного в центре, последовательность появления и таблица частот и форм колебаний; выявлено влияние размеров, материала диска и способов возбуждения колебаний. Studies of resonance frequencies and oscillation modes in constant-thickness disks with use of the holographic interferometryR.Kh. Makayeva, A.M. Tsaryova, and A.Kh. Karimov We present here some data on the resonance frequencies and oscillation modes in the centered constant-thickness disks. We established also the sequence of resonance frequencies/oscillation modes appearance and revealed the influence of the disk size, the material it is made from, and techniques of oscillation excitation. УДК 519.63 МЕТОД РЕДУКЦИИ В ЗАДАЧЕ ОПТИМАЛЬНОГО УПРАВЛЕНИЯ ВЫПЛАВКОЙ МЕТАЛЛА Р.Ф. Кадыров Рассматривается обратная коэффициентная задача, являющаяся математической моделью процесса оптимального охлаждения металла при его непрерывной выплавке. Задача состоит в подборе коэффициентов в краевых условиях третьего рода для двухфазной задачи Стефана с предписанной конвекцией [1, 2]. On the method of reduction in the problem about optimal control of metal MeltingR.F. Kadyrov We consider here the inverse coefficient problem, more specifically, the mathematical model for the process of optimal process of cooling at continuous metal making. The basic goal of this problem is the selection of coefficients at the Newton’s boundary conditions as applied to the two-phase Stephan’s problem with convection prescribed [1, 2]. The initial multi-dimensional problem of optimization can be reduced to a sequence of one-dimensional problems; these are convex in nature and can be solved without resorting to the gradient information. УДК 539.3 ОБ УЧЕТЕ ЭТАПНОСТИ СТРОИТЕЛЬСТВА ПРИ РАСЧЕТЕ НА ПРОЧНОСТЬ ПРОЛЕТНЫХ СТРОЕНИЙ МОСТОВ ИЗ СБОРНЫХ ЖЕЛЕЗОБЕТОННЫХ БЛОКОВ А.А. Пискунов, канд. техн. наук Выполнен анализ формирования полей НДС с учетом этапности монтажа сборных предварительно-напряженных железобетонных блоков пролетных строений мостов. Введено понятие трансформирующихся систем. Определена погрешность расчета без учета этапности формирования полей НДС. Проведен расчет по нетрансформирующейся и трансформирующейся схемам. On stage-by-stage approach to the construction of bridge superstructures from precast concrete blocks and calculation of their strengthA.A. Piskunov In this paper, we analyze the process of forming the stress-strained state (SSS) by taking account of step-by-step mounting of pre-cast pre-stressed concrete blocks of bridge spans and introduce the notion “transformable systems”. We revealed an error in calculations that are carried out without account of step-by-step approach to SSS field formation and conducted calculations by using both the transformable and non-transformable schemes of construction. Физика и химияУДК 537.312.62+541.123.3 НЕОДНОРОДНАЯ π-ФАЗНАЯ СВЕРХПРОВОДИМОСТЬ В НАНОСТРУКТУРАХ FM/S/FM Н.М. Иванов, ст. преподаватель, Л.А. Терентьева, ст. преподаватель, Развита оригинальная теория эффекта близости для трехслойных структур ферромагнитный металл/сверхпроводник/ферромагнитный металл (FM/S/FM). В отличие от предыдущих подходов предлагаемая теория учитывает пространственные изменения парной амплитуды как поперек FM- и S-слоев (1D-случай), так и в плоскости FM/S-границ (3D-случай). Принимается во внимание косвенное взаимодействие FM-слоев через электроны проводимости S-слоя, и допускается существование не только π-фазных магнитных состояний, но также π-фазных сверхпроводящих состояний в FM/S/FM-трислоях. Последнее состояние ранее считалось в принципе невозможным. Показано, что в FM/S-контактах процессы взаимного превращения пар БКШ и ЛОФФ на границе FM/S являются процессами переброса. Для FM/S/FM-трислоев авторами впервые предсказано существование четырех ЛОФФ состояний: 00, π0, 0π, ππ. Существование π-магнитных состояний 0π и ππ с антипараллельной ориентацией намагниченностей в FM-слоях позволяет объяснить неожиданно слабое подавление сверхпроводимости в короткопериодных сверхрешетках Gd/La, а также предсказать величину и знак электрон-электронного взаимодействия в гадолинии. Благодаря наличию различных сверхпроводящих и магнитных состояний трехслойные FM/S/FM-наноструктуры с двумя каналами записи информации в одном образце являются наиболее перспективными кандидатами для использования в сверхпроводящей спинтронике. Inhomogeneous π-phase superconductivity in nanostructures FM/S/FMN.M. Ivanov, L.A. Terent’yeva, D.S. Sattarov, and M.G. Khusainov We develop the original theory of proximity effect for the three-layer structures ferromagnetic metal/ superconductor/ ferromagnetic metal (FM/S/FM). Unlike the earlier existing approaches, this theory takes into account spatial variations of pair amplitude both crosswise the FM and S layers (1D case) and in the plane of FM/S boundaries (3D case). We take into account the indirect interaction of FM layers through the conduction electrons of the S layer and assume that there exist not only the π-phase magnetic states but also π-phase superconducting states in the FM/S/FM three-layers. The latter state was considered to be practically impossible. We show that the processes of mutual transformation between the BCS and LOFF pairs in the FM/S contacts at FM/S boundary are actually the umklapp processes. For the FM/S/FM three-layers the authors of this paper were the first to predict the existence of four LOFF states: 00, π0, 0π, and ππ. The existence of π magnetic states 0π and ππ with anti-parallel orientation of magnetizations in FM layers makes possible to explain the sudden effect of weak quenching of superconductivity in the short-period Gd/La superlattices and to predict the magnitude and sign of electron-electron interaction in gadolinium. Owing to the presence of different superconducting and magnetic states, the three-layer FM/S/FM nanostructures with two data-recording channels in one sample are the most promising structures for use in the superconducting spintronics. УДК 537.635;544 УСТАНОВКА НЕСТАЦИОНАРНОГО ДВОЙНОГО ЯДЕРНО-ЭЛЕКТРОННОГО РЕЗОНАНСА ДЛЯ ИССЛЕДОВАНИЯ ПРИРОДЫ ВЕЩЕСТВА Р.Г. Яхин, канд. физ.-мат. наук, Б.А. Тимеркаев, докт. физ.-мат. наук Выясняется возможность метода импульсного двойного ядерно-электронного резонанса в исследовании структуры и свойств веществ-растворов некоторых парамагнетиков. Для этого была разработана методика и сконструирована действующая установка нестационарного двойного ядерно-электронного резонанса, работающая в промежуточных магнитных полях с использованием импульсной развертки внешнего магнитного поля. Приведены результаты экспериментальных исследований частотно-температурной зависимости динамической поляризации в растворах некоторых координационных соединений. Рассматривается вопрос о природе молекулярного обмена и роли молекулярной диффузии в формировании эффекта динамической поляризации ядер. Ibstallation of nonstationary electron nuclear double resonance for studies of substance natureR.G. Yakhin and B.A. Timerkayev In this paper, we discuss a feasibility of pulse electron nuclear double resonance method for studying the structure and properties of substances (solutions) in some paramagnetic materials. For this, we designed and fabricated the operating installation of nonstationary electron nuclear double resonance that is capable to work in the intermediate magnetic fields and uses the pulse sweep. We present the results of experimental studies of temperature-frequency dependence of dynamic polarization in solutions of some coordination compounds. Also considered is problem concerning the nature of molecular exchange and the role of molecular diffusion at formation of nucleus dynamic polarization effect. УДК 533.9:543.42 ВЛИЯНИЕ ПУЛЬСАЦИЙ ИНТЕНСИВНОСТИ ИЗЛУЧЕНИЯ ПЛАЗМЫ НА ТОЧНОСТЬ ИЗМЕРЕНИЯ РАДИАЛЬНОЙ ТЕМПЕРАТУРЫ Б.А. Тимеркаев, докт. физ.-мат. наук, Р.С. Тухватуллин, канд. техн. наук Предложена модель осесимметричной нестационарной плазмы; найдены функции распределения этих колебаний рассчитаны радиальные температуры плазмы с учетом этих колебаний. Influence of pulsations in plasma radiation intensity upon measuring accuracy of radial temperatureB.A. Timerkayev and R.S. Tukhvatullin We suggest using here the model of axisymmetrical unsteady plasma. For this, we found the functions of pulsation distribution and calculated the radial temperatures of plasma. Информатика и управлениеУДК 681.511:621.643 СИНТЕЗ СОСРЕДОТОЧЕННОГО УПРАВЛЕНИЯ ТРАНСПОРТИРОВКОЙ УГЛЕВОДОРОДНОГО СЫРЬЯ ПО ДЛИННЫМ ТРУБОПРОВОДАМ Л.О. Мурга, аспирант Формулируется и решается задача синтеза управления транспортировкой углеводородного сырья по длинным трубопроводам как задача синтеза неграничного управления распределением расхода по всей длине трубопровода. On synthesizing the concentrated control of hydrocarbon raw material transportation through long pipelinesL.O. Murga We formulate here the problem on synthesizing the control of hydrocarbon raw material transportation through long pipelines. The problem is solved as the problem of synthesizing the non-boundary control of flowrate distribution throughout the entire pipeline length. УДК 681.527.34 ОПЫТ ПРИМЕНЕНИЯ МИКРОПРОЦЕССОРНЫХ СИСТЕМ УПРАВЛЕНИЯ НА ТЯЖЕЛЫХ ТРАНСПОРТНЫХ МАШИНАХ Г.Л. Дегтярев, докт. техн. наук, А.А. Маханько Обобщен опыт разработки микропроцессорных систем управления трансмиссией для бульдозеров-рыхлителей и колесных погрузчиков производства ОАО «Промтрактор». Основной задачей разработанных систем является обеспечение плавности работы трансмиссии и повышение из-за этого срока их службы. При разработке законов управления использовался метод математического моделирования процессов в гидросистеме. On experience gained in the field of using the microprocessor systems on heavy-duty transport vehiclesG.L. Degtyaryov and A.A. Makhan’ko In this paper, we generalize the experience gained by OOO «Promtraktor»in the field of microprocessor УДК 519.217.4 ИССЛЕДОВАНИЕ ПРЕДЕЛЬНЫХ ОТКЛОНЕНИЙ ПАРАМЕТРОВ ПРИЗЕМЛЕНИЯ ТЯЖЕЛЫХ САМОЛЕТОВ ПРИ АВТОМАТИЧЕСКОЙ ПОСАДКЕ К.Г. Денисов, аспирант Рассматривается практическое применение метода экстремальных возмущений для оценки статистических характеристик и предельных отклонений компонент вектора состояний самолета ИЛ96-300 и его систем в процессе автоматической посадки. Investigation of deviation limits in the parameters of heavy aeroplane touchdown at automatic landingK.G. Denisov We consider here the practical application of the extreme disturbance method for evaluation of statistical characteristic and deviation limits in the components of the aeroplane IL96-300 vector of states and its systems at automatic landing. Моделирование и управление процессамиУДК 519.339 ФАКТОРНАЯ МОДЕЛЬ ПРОГНОЗА ФИНАНСОВОГО СОСТОЯНИЯ ПРЕДПРИЯТИЯ Г.П. Потапов, докт. техн. наук, Е.И. Галеева, канд. техн. наук,
Р.Н. Ахунов, аспирант Предлагается математическая модель прогноза рентабельности собственного капитала предприятия. On a factor model for prediction of an enterprise’s financial stateG.P. Potapov, E.I. Galeyeva, and R.N. Akhunov We suggest using the mathematical model for prediction of profitability of an enterprise’s property assets and show the profitability dependence on profitability of sales, turnover of assets, and their ratio to the enterprise’s proprietary funds. УДК 621.372.22+658.512.2.011.56.001.2 КОНЦЕПЦИЯ И ПРОБЛЕМЫ СОЗДАНИЯ ПРОГРАММНОГО КОМПЛЕКСА ДЛЯ АНАЛИЗА И СИНТЕЗА УСТРОЙСТВ
НА ОСНОВЕ RC-ЭЛЕМЕНТОВ С РАСПРЕДЕЛЕННЫМИ ПАРАМЕТРАМИ.
|
2007 1 |